Forums > Land Yacht Sailing General

Windsurfer sail rigging

Reply
Created by phum 1 month ago, 29 Jun 2022
phum
QLD, 19 posts
29 Jun 2022 5:36PM
Thumbs Up

Hello all, Does anybody have photos of how they rigged the mainsheet on a windsurfer boom onto a LLM?
Thanks,
Peter

mulgachook
NSW, 29 posts
29 Jun 2022 8:51PM
Thumbs Up








G'day Peter, A bit rough and ready but we have been rigging our windsurfer booms with two individual pulleys, one each side of the sail. A few wraps of blind cord go from side to side on the boom and the pulleys are supported off this. As well more blind cord ties this mess back to the end of the boom to stop it pulling forward. Each block is tied to prevent it slipping sideways. Otherwise same set up as with a single boom, tie off to seat support, up to pulley on boom, back down to pulley on seat support, up to other pulley on boom then forward to the mast / sail pulley, down to mast base pulley and back to pilot. If you can rig the sheet to go forward to the mast and clear the sail it works well otherwise there can be problems gybing with the released sheet dragging against the sail and not releasing !!! A little bit of overlap is manageable, the setup on the front yacht above worked well. The yacht behind it would misbehave gybing if you forgot to reach up and give the sheet a shake to loosen it when turning. Long booms on short sails can help with clearance but are unwieldy. If the shape of the sail lets you use a straight landyacht boom it is a better option.

phum
QLD, 19 posts
30 Jun 2022 10:18AM
Thumbs Up

thanks mate

Chook2
WA, 1242 posts
1 Jul 2022 5:44PM
Thumbs Up

Phum's new yacht. He asked me to post these pics for him.
Sorry about the delay mate.











phum
QLD, 19 posts
2 Jul 2022 3:47PM
Thumbs Up

Thanks Chook2.
You 2 chooks have been more than helpfull, I do appreciate itpeter

phum
QLD, 19 posts
3 Jul 2022 1:52PM
Thumbs Up

I should thank Ben to for his advice.
The frame is to the LLM diamensions but the material differs. I had to use what I could buy, scrap here is really scrap and nearly as dear as new steel.
The seat I changed to try and make it more comfortable than the last one but that was probably a mistake given my poor carpentry skills. I have a 4.8 windsurfer rig I am going to start with

kennatt
134 posts
4 Jul 2022 3:46PM
Thumbs Up

No need to use windsurf boom unless the sails are very,very old soft unbatton sail. battoned Windsurf sails fully downhauled are extremly stable and can be used with a conventional under sailboom If you enter seabreeze general page 2 in search you should get all the old postings look for useing uncut sails by a poster , By the north sea , been discussed at length.

phum
QLD, 19 posts
5 Jul 2022 12:26PM
Thumbs Up

Cant find page 2. Where is it?

kennatt
134 posts
5 Jul 2022 4:55PM
Thumbs Up

Tried to cut and paste site but fails but by inserting Seabreeze land yachts general forum page 2 in search engine brings up page in micro edge

phum
QLD, 19 posts
6 Jul 2022 8:24AM
Thumbs Up

I cant find it can you send me a link please

kennatt
134 posts
6 Jul 2022 7:54PM
Thumbs Up

www.seabreeze.com.au/forums/Land-Yacht-Sailing/General?page=2

Look for uncut windsurf sails

phum
QLD, 19 posts
7 Jul 2022 3:52PM
Thumbs Up

thanks sir

kennatt
134 posts
7 Jul 2022 11:12PM
Thumbs Up

www.seabreeze.com.au/forums/Land-Yacht-Sailing/Construction?page=2

You may find the above usefull it brings up all the old posts



Subscribe
Reply

Forums > Land Yacht Sailing General


"Windsurfer sail rigging" started by phum