ratz said..
my old carbon boom needs regripping.
does anyone have any ideas about who does this in perth.
thanks in advance..

Hydrodynamix used to.

Steve Strathfold has done it before

the other alternative is to look in the mirror and mutter

elmo said..

ratz said..
my old carbon boom needs regripping.
does anyone have any ideas about who does this in perth.
thanks in advance..

Hydrodynamix used to.

Steve Strathfold has done it before

the other alternative is to look in the mirror and mutter

i dont think so elmo.
i want a decent job done..my quality control standards are sadly lacking.

Windxtasy said..

ratz said..

elmo said..

ratz said..
my old carbon boom needs regripping.
does anyone have any ideas about who does this in perth.
thanks in advance..

Hydrodynamix used to.

Steve Strathfold has done it before

the other alternative is to look in the mirror and mutter

i dont think so elmo.
i want a decent job done..my quality control standards are sadly lacking.

It's not so difficult. I did mine and the regrip has lasted a couple of seasons so far. The hard part is getting all the old grip off a carbon boom.

..and since Severne showed us that its easy using thinners, its not so hard any more. The thinners trick is incredible. The grip just falls off and makes you wonder why no one knew of it before.

ratz said..
my old carbon boom needs regripping.
does anyone have any ideas about who does this in perth.
thanks in advance..

Mr Stratfold is the guru, did a great job on my carbon MS boom , it looks like new as I got the original MS grip from Paul @2nd wind and Steve fitted it

Has anyone re-gripped their boom with the seam on the outside?

I have a couple of carbon Chinook booms, and both of them have/had sections where I have ripped off the grip just from gripping it with my hands. Chinook also have their lettering and different colours done with different pieces of eva grip.

I looked at where my fingers rest and where they grip under pressure, and the only place I could think of was the outside, half way up.

Am I going to regret this and end up ripping my grip off really easy?

Another bonus I got was that the replacement grip I fitted from SSA seems to be thinner than the original grip, so it feels more solid, and a slightly smaller diameter.

ratz said..
most of grip already gone.
will try thinners tomorrow to get the rest off.
can you still buy boom regrip kits.?

Surf sail australia has them
The main trick, I found, is to stretch the grip lengthwise a little as you go around the curve at the front of the boom.
This makes it curl around the boom and also eliminates puckers on the inside.

FormulaNova said..
Has anyone re-gripped their boom with the seam on the outside?

I have a couple of carbon Chinook booms, and both of them have/had sections where I have ripped off the grip just from gripping it with my hands. Chinook also have their lettering and different colours done with different pieces of eva grip.

I looked at where my fingers rest and where they grip under pressure, and the only place I could think of was the outside, half way up.

Am I going to regret this and end up ripping my grip off really easy?

Another bonus I got was that the replacement grip I fitted from SSA seems to be thinner than the original grip, so it feels more solid, and a slightly smaller diameter.

I have got two NP X9s both have been re-gripped, one has the seam on the inside,the other on the outside.
IMO the one with the seam on the outside is better for me as your fingers do seem to put to much wear on the
seam.

shear tip said..

sausage said..... I recall Kimba did an instructional video too so will chase up link.
...

I followed Kimba's blog to re-grip mine:

whitelionwindsurfing.blogspot.com/2012/02/diy-windsurf-boom-re-grip.html

I used those instructions too. Worked well for me.