DIY Project Help!

> 10 years ago
Reply
Register to post, see what you've read, and subscribe to topics.
raggy
raggy
VIC
564 posts
VIC, 564 posts
20 Jan 2016 2:02pm
Hay I'm thinking of building a Spit out of a 44 gal drum i have. only thing is i cant decide the best way to clean it out so i can cut it safely? any one had experience in this area>
Tux
Tux
VIC
3829 posts
Tux Tux
VIC, 3829 posts
20 Jan 2016 2:24pm
Steam
Tin snips
Sailhack
Sailhack
VIC
5000 posts
VIC, 5000 posts
20 Jan 2016 3:37pm
Depending on what's been in it? If fuel or non-solid-forming liquid - put 20lts or more of hot water & ample detergent (cup of washing powder is good), swish around, let settle a few times & empty. Put in another few lts of water but leave in. Ensure that the lid/cap is off for ventilation and with a fire extinguisher handy & good PPE get stuck into it with a grinder and 1mm cutting disc!

DON'T try this if it stored a solid-forming liquid (some oils, grease, paint etc) as the water won't remove the solids and they may become explosive.

Nibblers are also handy, but a grinder will get the job done smoother & faster.
Tequila !
Tequila !
WA
1028 posts
WA, 1028 posts
20 Jan 2016 1:02pm
Fill it with water and some laundry soap (shall assist with any grease of oils stuck if the contains are a concern)...leave it a day or two.

Empty then cut with your preferred tool (angle grinder with thin cut off wheel works better). Scribe the half line prior starting.

My BBQ half cut drums usually last around 2 to 3 years kept out of rain. The last one I ''relined'' with some colourbond I had left over.


felixdcat
felixdcat
WA
3519 posts
WA, 3519 posts
20 Jan 2016 1:06pm
fill it with water to degas it
actiomax
actiomax
NSW
1576 posts
NSW, 1576 posts
20 Jan 2016 4:16pm
Steam clean is good flush with hot water it lets chemicals out of the steel alternatively put it on a fire with plugs out &give it a good burn its what's going to happen after all better to burn all the **** out than flavour your meat.
cameron2156
cameron2156
WA
149 posts
WA, 149 posts
20 Jan 2016 5:33pm
Made a smoker out of one. Put a fire in mine and let it rage for an hour then got on the grinder to get all the paint off. U have to take all the paint off the drum as it will not be good for u an the food with chemicals in the paint
Mark _australia
Mark _australia
WA
23677 posts
WA, 23677 posts
20 Jan 2016 5:42pm
Wash as per above suggestions, then dry. Then fill (like really fill and let tons of excess escape so it is well flushed) with Argon, CO2 etc from a MIG before cutting with an angle grinder and thin blade


FormulaNova
FormulaNova
WA
15101 posts
WA, 15101 posts
20 Jan 2016 6:26pm
Has anyone had any fun with a recipro saw and metal cutting blades? I used one to cut up the remains of a car and they worked much better than an angle grinder in that they generate less grit and seem to be faster too.

Kozzie
Kozzie
QLD
1451 posts
QLD, 1451 posts
20 Jan 2016 9:40pm
shoot it with a gun then use the hole to get ya nips in there and cut it out manually
Test pilot 1
Test pilot 1
WA
1430 posts
WA, 1430 posts
20 Jan 2016 8:48pm
Get a long extension cord or 2 (at least 50m long)and wrap tape around the female end until it fits snugly into the big hole, then put a piece of 10 amp fuse wire into the phase and neutral holes to short it out, fill drum with oxy-acetylene gas mix and jam plug end into big hole. Stand well clear(50mtrs), plug into power socket and turn on. Blank end becomes a wok hole end becomes a wok with holes and side becomes flattish.
Beware of sharp edges!
Works on varnish 44's
Chris6791
Chris6791
WA
3271 posts
WA, 3271 posts
20 Jan 2016 9:38pm
I don't get why you wouldn't scrounge a food grade drum from somewhere, no nasty chemicals, no paint to burn off, no risk of blowing your head off and you're not cooking for the in-laws in an old petrol tank... oh wait, never mind
chrispy
chrispy
WA
9675 posts
WA, 9675 posts
20 Jan 2016 10:45pm
Chris6791 said...
I don't get why you wouldn't scrounge a food grade drum from somewhere, no nasty chemicals, no paint to burn off, no risk of blowing your head off and you're not cooking for the in-laws in an old petrol tank... oh wait, never mind


You still need to burn out the inside of a food grade drum before you can cook in it as it is lined with a coating. You just don't have to worry about blowing yourself up when cutting it open.

You can pick up a food grade drum for $20,

How many kg of animals are you wanting to cook? As a beer keg might be a better option for you

raggy
raggy
VIC
564 posts
VIC, 564 posts
21 Jan 2016 7:45am
I wanted a Keg to start with but do know where to look for one. A Keg would be perfect?
jonnulla
jonnulla
NSW
74 posts
NSW, 74 posts
21 Jan 2016 9:18am
if your looking for an empty one then try any pub in Australia this wednesday, if your looking for a full one, go there on monday ;)
Sailhack
Sailhack
VIC
5000 posts
VIC, 5000 posts
21 Jan 2016 11:52am
If you get hold of a keg, just don't advertise the number stamped/pressed on the side or you'll have CUB on your back.
Kozzie
Kozzie
QLD
1451 posts
QLD, 1451 posts
21 Jan 2016 8:33pm
jonnulla said..
if your looking for an empty one then try any pub in Australia this wednesday, if your looking for a full one, go there on monday ;)


the dolls paid out on thursdays these day cob
Please Register, or first...
Topics Subscribe Reply